Are you in search of additional info about Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't exactly rocket science, but it does require solid plumbing, woodworking, and sometimes, tiling skills. Changing an old tub with a new one is also a moderately challenging job. If the old bathtub is easily accessible, the job can move easily; if you have to open up a wall to remove the old bathtub and also position the brand-new tub, the task is much harder. In either instance, the project is within a residence handyman's skills, although you will need a helper to leave the old tub and also embeded in the brand-new one. Make sure you have certified on your own for the work and fit trying it. Rather than working with a professional to take over a halfway-completed job, it is far better to take into consideration utilizing one prior to you start. Opportunities are you may require a professional plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't require to transform the plan of your previous water pipelines.
Your tools as well as material checklist ought to make up the following:
Planning for the Installation
First of all, the sustaining framework supplied with the bathroom needs to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to prevent stress on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last setting.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is detach the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome due to the limited accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the continuing to be water that will originate from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing both wooden boards under its feet, place the bath tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also readjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the furthest adaptable tap connector to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water supply as well as examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bath tub and additionally check the overflow electrical outlet and also the normal outlet for leaks.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and also securing around the bathtub needs to wait until the bath tub has been utilized a minimum of once as this will settle it right into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the manufacturer supplied backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type needs to be linked to the faucet ends first, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a stiff seal, triggering the water to permeate the wall between the bathroom and also the tiling, causing issues with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to permit the activity experienced when the tub is in usage. The sealer can break rather early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you liked our excerpt about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking time to browse our article. Enjoyed our blog entry? Please share it. Let somebody else check it out. We cherish reading our article about A Step-by-Step Guide to Installing a Bathtub.
Source